Product Catalog
Request Information
Shell Gadus S2 High Speed Coupling Grease is specially formulated with a lithium soap/polymer thickener, which has superior resistance to oil separation when subjected to the high centrifugal forces normally found in couplings.
Unit of Measure

Package Type

 N/A Keg

Thickener Type

 N/A Lithium Soap/Polymer

National Lubricating Grease Institute (NLGI) Consistency

 N/A 0/1

Color

 N/A Dark Brown

Viscosity at 40 Degree Celsius (ºC)

N/A 3200 cSt

Viscosity at 100 Degree Celsius (ºC) Temperature

 N/A 50 cSt

Drop Point

 N/A 320 ºF

Timken OK Load

 N/A 40 lb

Four Ball Load Wear Index

 N/A 68 kgf

Four Ball Weld Point

 N/A 400 kg

Four Ball Wear Scar Diameter

 N/A 0.4 mm

60 Strokes Worked Penetration

 N/A 350

10,000 Strokes Worked Penetration, % Change

 N/A 10

Rust Protection

 N/A Pass

Water Sprayoff Loss

 N/A 3 %

Centrifugal Oil Separation

 N/A None

Thickener Content

 N/A 10 %

Guide to Useable Temperature (Pumping), Minimum

 N/A -6 ºC20 ºF

Guide to Useable Temperature (Bearings), Minimum

 N/A -23 ºC-10 ºF

Guide to Useable Temperature (Couplings), Minimum

 N/A Below -29 ºCBelow -20 ºF

Continuous Service Temperature, Maximum

 N/A 120 ºC250 ºF

Short Exposure Temperature, Maximum

 N/A 160 ºC325 ºF

Additional Information

 N/A The tacky nature of the product makes hand packing the preferred method of newly installed couplings to ensure even distribution throughout. Normal handling precautions should be observed as with any petroleum based products. Consult the coupling manufacturer's installation instructions for detailed lubricant application procedures. The following procedure outlines a popular lubrication method. Prior to assembly of gear couplings a coating of grease should be applied to gear teeth. After hand packing, the coupling should be rotated so the grease fitting reaches 4 o'clock, and the fitting/plug removed. A short length of 1/4 inch pipe can be affixed and grease pumped into the coupling until product is observed flowing out the purge opening at 10 o'clock. The pipe should then be removed and the plugs reinserted. This practice insures that the coupling is adequately lubricated. Routine relubrication can be accomplished with disassembly using this method. The grease will then be evenly distributed to all moving and sliding surfaces and the full benefits of the product will be realized. Special care needs to be taken when filling "Full Travel" type couplings so the correct amount of grease is charged.

Applications

 N/A Shell Gadus S2 High Speed Coupling Grease is recommended for all types of grease lubricated couplings in industrial equipment. Common grease lubricated couplings include:
  • Geared Couplings which have internal and external spur gears that mesh within a common rotating hub connecting the shafts
  • Steel Grid Couplings which have a covoluted band of flexible spring steel physically linking the hubs together
  • Flexible Chain Couplings which have a roller chain that meshes with a sprocket cut in each mating hub
Advanced technology has enabled Shell Gadus S2 High Speed Coupling Grease to perform beyond the normal 6 months change interval. In actual field experience this grease has shown its ability to perform satisfactorily beyond 3 years. This product should be used in all grease couplings, especially in those hard to service or those operating under severe conditions.

Because of its high base oil viscosity, Shell Gadus S2 High Speed Coupling Grease is also suitable for use in other industrial applications where the equipment is subject to high water wash, low speeds and heavy or shock loads.

Features and Benefits

 N/A
  • Resistance to centrifugal separation
  • Extended relubrication frequency
  • High load carrying capabilities
  • Resistance to water washing
  • Staying in place under high speeds
  • Corrosion and rust protection
  • Minimizing of coupling wear
  • Reduction in down time and maintenance costs
  • Minimizing of coupling freeze-up
  • Use at temperatures up to 325 F
  • One grease for all grease coupling types
  • Shell Gadus S2 High Speed Coupling Grease has a consistency which overlaps the NLGI grades 0 and 1. This grease is specially formulated with a lithium/polymer thickener and fortified with corrosion, oxidation, extreme pressure and an effective rust inhibitor additive package.
  • Its high viscosity base oil and tackifier combine to keep the grease in place and prevent separation. In the ASTM D4425, High Speed Centrifugal Test, which develops G forces in excess of 36,000 at 15,000 rpm. Shell Gadus S2 High Speed Coupling Grease exhibits little or no oil separation.
  • Based on ASTM D1478 and D4693 torque tests, the minimum recommended bearing lubrication service would be -10 F. For coupling service the minimum usable temperature is not dependent upon ease of pumping or bearing breakaway force. Field service confims problem-free coupling service at -20 F and below. Actual minimum temperature for coupling service would be below -20 F.

Claims (Meets Requirements)

 N/A AGMA Type CG- 1 AGMA Type CG-2 AGMA Type CG-3

Claims (Suitable for Use)

 N/A Browning Couplings Falk Couplings Fast Couplings Koppers Couplings TB Woods Couplings